Operating InstructionsCode 790 044 762GEORG FISCHER +GF+RA 21 and RA 21 SpecialPipe Cutting andBevelling Machines
6GEORG FISCHER +GF+¹The following materials can be used:º steel, black or galvanisedº chrome and stainless steel(up to 2.5 mm wall thickness)º alumin
7GEORG FISCHER +GF+4 Technical specificationsManufacturer Georg FischerRohrverbindungstechnik GmbHD-78224 SingenDimensions 300 x 450 x 300 mmWeight(i
8GEORG FISCHER +GF+¹5 Commissioning5.1 Checking the scope of deliveryCheck all parts of the delivery for completenessand transport damage. Please rep
9GEORG FISCHER +GF+5.2 Transporting and assembling the pipe cutterTransportDisconnect from the power supplybefore transporting, mounting ordismountin
10GEORG FISCHER +GF+¹6 Operation6.1 Fitting the saw blade /additional cutterDisconnect the mains plug before fittingor changing the tool.The saw blad
11GEORG FISCHER +GF+Fitting the saw blade!Mount the followingon the shaft (1):º saw blade (3)º clamping disk (4)code RA 21:790 041 188code RA 21 S:79
12GEORG FISCHER +GF+¹1/43/81/23/4111/411/221236.2 Adjusting the pipe diameterThreaded pipes to DIN 2440!Release the lever(1).!Select pipe diameteron
13GEORG FISCHER +GF+6.3 Adjusting the additional cutterSimultaneous cutting and bevelling of steel pipesup to a wall thickness of 4.5 mm is possible.
14GEORG FISCHER +GF+¹6.4 Using stopsLength gauge up to 250 mm!Mount the lengthgauge (1).!Swing the stop (2) into the middle of thepipe and engage.!Re
15GEORG FISCHER +GF+!Tighten the clamp.!Push the pipe upagainst the stopand clamp.!Swing the stop outand push all theway back.!Cut the pipe.!For the
These operating instructions are partof machine no.: ...All rights retained, in particular the rights to reproduction, dissemina
16GEORG FISCHER +GF+¹!Mark the cuttinglocation on thepipe.!Insert the pipe in thevise.!Push the markedcutting location overthe saw blade.!Clamp the p
17GEORG FISCHER +GF+!Switch on the sawmotor. Press the on/off switch (1) andthe locking button(2).!Carefully turn thepipe cutter clock-wise until the
18GEORG FISCHER +GF+¹6.6 Cutting and bevelling the pipeThis procedure combines cutting and bevellingof the pipe. When cutting and bevelling simul-tan
19GEORG FISCHER +GF+!Switch on the sawmotor. Press the on/off switch (1) andthe locking button(2).!Carefully turn thepipe cutter clock-wise until the
20GEORG FISCHER +GF+¹7 MaintenanceDisconnect the mains plug beforedoing maintenance work.Intervalevery weekActivityRemove the saw blade and brush off
21GEORG FISCHER +GF+Intervalafter the first 150 hoursof operation(or after 3 months,whichever is sooner),then every 1000 hours ofoperation (or every
22GEORG FISCHER +GF+¹8 What to do if ...?CauseLocking screw tightened.Wrong pipe diameterset.Nut on saw blade shaftnot tight enough.Saw blade wrong w
23GEORG FISCHER +GF+Service / after-sales serviceSpare parts: see separate spare parts list.Separate service instructions are available forthe elimin
GEORG FISCHER +GF+A Georg Fischer Rohrleitungssysteme GmbH, Sandgasse 16, 3130 Herzogenburg,Tel. +43(0)2782/8 56 43-0, Fax +43(0)2782/8 56
IGEORG FISCHER +GF+Table of ContentsPage0 About these operating instructions 11 Notes on safety 22 Description of the pipe cutter 43 Features and sco
IIGEORG FISCHER +GF+
1GEORG FISCHER +GF+0 About these operatinginstructionsThe symbols used in this manual are explainedhere to help you quickly understand theoperating i
2GEORG FISCHER +GF+¹1 Notes on safetyThe RA 21/RA 21 Special Pipe Cutting andBevelling Machine (referred to as a pipe cutterin the following) is a st
3GEORG FISCHER +GF+Working with safety in mind"Make your contribution to safety at the workplace."Report any unusual behaviour on the part
4GEORG FISCHER +GF+¹2 Description of thepipe cutterThe pipe cutter is a robust, user-friendly,service-friendly and safety-oriented design.Vise and sa
5GEORG FISCHER +GF+3 Features and scope ofapplication of the pipecutterThe pipe cutterº is a fully configured working machine suitablefor workshop an
Comments to this Manuals